12V LiFePO4 Lead-Acid Replacement: Voltage, Fit and Charging Rules

Most lead-acid replacements fail on three numbers nobody checks before the order. A buyer compares amp-hours, sees 100 Ah against 100 Ah, and assumes the lithium pack is a drop-in part. It is not. The nominal voltage is different, the charge acceptance is different, and the discharge limit is lower than the lead-acid block it replaces. Each of those differences is small on paper and expensive in the field.

This page sets out what actually changes when a 12 V lead-acid battery is replaced with a LiFePO4 pack, why a 60 V fleet needs a 64 V pack rather than a 60 V one, and which three checks decide whether a replacement is safe before it is quoted. It is written for distributors, installers and fleet workshops who resell or fit these packs, not for a one-off DIY swap.

Short answer: a lead-acid replacement pack is specified by four numbers, not one. Match the voltage string to the old bank (12 V lead becomes 12.8 V, 60 V becomes 64 V, 72 V becomes 76.8 V), confirm the tray by measuring rather than by group number, confirm the charge current your charger or DC-DC can deliver is inside the pack’s rated charge, and confirm the discharge limit clears your largest load. Get those four right and the pack lasts; get the third or fourth wrong and it will be returned.

Why the voltage changes · Check 1: fit · Check 2: charge current · Check 3: discharge current · Charging below 0 °C · Series and parallel · The six configurations · Where it does not work

Why a 12 V replacement is 12.8 V — and a 60 V fleet needs 64 V

Lead-acid and LiFePO4 count cells differently. A lead-acid cell is about 2.0 V nominal, so six of them make the 12 V battery everyone recognises. A LiFePO4 cell is about 3.2 V nominal, so it takes four to reach 12.8 V. The pack is doing the same job at the same string length — it simply uses fewer, larger cells to get there.

That arithmetic is why replacement packs are listed at voltages that look wrong next to the battery they replace. A 48 V lead-acid bank is 24 lead cells, which becomes 16 LFP cells and a 51.2 V pack. A 60 V bank is 30 lead cells, 20 LFP cells, 64 V. A 72 V bank is 36 lead cells, 24 LFP cells, 76.8 V. The series count — printed on our listings as 1P20S, 1P24S and so on — is the specification that matters, because it is what determines whether the pack sits inside the controller’s and charger’s voltage window.

Lead-acid bankLead cellsLFP series countLFP pack nominal
12 V6S4S12.8 V
24 V12S8S25.6 V
48 V24S16S51.2 V
60 V30S20S64 V
72 V36S24S76.8 V

Two consequences follow, and both catch buyers out. First, the working voltage range shifts: our 12.8 V configurations are listed at 10–14.6 V, against roughly 10.5–14.4 V for a flooded lead-acid block. A controller with a 10.5 V low-voltage cutoff will therefore run the pack slightly past the bottom of its range before it trips. Second, and more common, a charger built for lead-acid finishes at float — often 13.6–13.8 V — which is below what a LiFePO4 pack needs to reach full charge. The pack is not faulty; it is simply never being filled.

This is the point at which most replacement projects should stop and re-specify the charger. If the existing charger has no lithium profile and no adjustable absorption voltage, the honest answer is that the pack will work at partial state of charge — usable, but not what the capacity figure promises. Say so before the order, not after.

Check 1 — will it fit, and does the tray hold it?

Group numbers are a starting point, not a specification. Terminal height, hold-down lip, base footprint and cable routing all vary between vehicles that take the same nominal group, and a lithium pack’s case is usually a different shape from the lead block it replaces even when the footprint matches.

Measure the tray in three dimensions including the terminals, then compare against the listed dimensions. Our four 12.8 V configurations are listed as follows; the dimensions are the brochure figures and must be confirmed against the supplied configuration before a PO is placed, because a family image can be shared across configurations with different case sizes.

ConfigurationNominal energySeries/parallelDimensions (as listed)Mass (as listed)
12.8 V 25 Ah320 Wh1P4S181 × 77 × 170 mm≤3.88 kg
12.8 V 50 Ah640 Wh2P4S198 × 166 × 170 mm≤5.26 kg
12.8 V 75 Ah960 Wh3P4S260 × 168 × 209 mm≤7.64 kg
12.8 V 100 Ah1,280 Wh4P4S330 × 172 × 215 mm≤9.52 kg

Mass is the number installers notice first. A 12.8 V 100 Ah pack is listed at ≤9.52 kg. Weigh the lead-acid unit being removed rather than trusting a datasheet — the difference is usually the reason the customer is converting in the first place, and it is also the reason a bracket that was adequate for the old block may need a second look.

All six configurations are listed at IP67. That is the manufacturer’s rating for the pack, not for the connector, the fuse holder or the cable entry — those are the parts that let water in on a vehicle, and they are specified separately.

Check 2 — will the charger stay inside the pack’s charge limit?

This is the check that decides most warranty arguments. A lead-acid battery of 100 Ah will absorb whatever a 30 A charger gives it, for as long as it takes. A LiFePO4 pack has a rated charge current, and exceeding it continuously is a stress the BMS may or may not police depending on how the configuration is built.

Our 12.8 V listings carry both a rated and a maximum continuous charge current. The rated figure is the number to design the charging system around; the maximum is a ceiling, not a target.

ConfigurationRated chargeMax continuous chargeRated dischargeMax continuous discharge
12.8 V 25 Ah12.5 A (0.5C)25 A (1C)12.5 A (0.5C)50 A (2C)
12.8 V 50 Ah25 A (0.5C)50 A (1C)25 A (0.5C)100 A (2C)
12.8 V 75 Ah37.5 A75 A37.5 A100 A
12.8 V 100 Ah50 A100 A50 A100 A

Worked example, because this is where quotes go wrong. A 12.8 V 25 Ah pack has a rated charge of 12.5 A. Fit a 30 A DC-DC charger and you are asking for 2.4 times the rated current on every drive. The pack may accept it — the maximum is listed at 25 A — but the thermal margin is gone and the cycle life claim no longer describes what the pack is doing. Either step up to the 50 Ah configuration or specify a smaller DC-DC. That decision belongs in the quotation, not in the workshop.

On vehicles with an engine-driven alternator, the same logic applies through a different route. An alternator regulated for lead-acid holds a voltage that will not fully charge a LiFePO4 pack, and connecting one directly risks a charge profile the pack was not specified for. A DC-DC charger with a lithium profile is the normal answer; a direct connection is not, unless the alternator’s regulation has been checked against the pack’s charge window and confirmed by the vehicle builder.

Check 3 — will the pack deliver the current your load asks for?

Amp-hours tell you how long. They do not tell you how hard. The discharge limit is a separate figure, and it is the one that decides whether an inverter, a winch or a hydraulic pump will trip the BMS on the first cold morning.

Take the load in watts, divide by the pack’s nominal voltage, divide again by the inverter’s efficiency, and compare the result with the maximum continuous discharge current. A 2,000 W inverter running from a 12.8 V pack at roughly 90% efficiency draws about 174 A. The 12.8 V 100 Ah configuration is listed at 50 A rated and 100 A maximum continuous discharge, so a single unit is not the right answer for that load — two in parallel, or a move to a 48 V-class system, is.

The same calculation, run the other way, is how a replacement gets sized properly. If the largest continuous load is a 600 W pump, the draw at 12.8 V is about 52 A — which means the 75 Ah or 100 Ah configuration clears it on rated discharge, while the 50 Ah clears it only at its maximum. Two different quotes, both technically correct, with very different service life.

Charging below 0 °C is the failure that is invisible on a datasheet

Our listed configurations charge between 0 and 55 °C and discharge between −20 and 60 °C. Those two numbers are not symmetric, and the asymmetry is the whole point: a LiFePO4 pack can deliver energy below freezing, but charging it below 0 °C causes lithium plating on the anode, which is permanent and shows up months later as lost capacity rather than as an immediate failure.

So the question to put to any supplier is not whether the pack has low-temperature protection, but whether the BMS blocks charging below 0 °C while still allowing discharge — and whether it does that on the charge path the vehicle actually uses. A pack protected on the mains charger but not on the alternator or DC-DC path is unprotected in the case that matters.

For fleets operating below freezing, a heated pack or a temperature-managed enclosure is the engineering answer, and it should be raised at specification time. Our listed configurations do not include heating; if the duty cycle requires charging at sub-zero ambient, say so in the enquiry and the configuration will be assessed rather than assumed.

Series and parallel: what the BMS must actually support

Our 12.8 V 100 Ah configuration is listed as 4P4S. That describes the internal arrangement of cells inside one case. It does not mean the finished pack can be connected in series with three others to make a 48 V string. External series connection is a property of the BMS and the pack design, and it has to be specified.

If a project needs a 48 V string built from four 12.8 V units, the requirements are: a BMS rated for series operation, per-pack balancing that survives a mid-string failure, and a documented answer to what happens when one pack in the string trips. Without those three, a series string of four independent packs is four single points of failure stacked on top of each other.

Parallel connection is more forgiving, and is the normal answer for increasing capacity or discharge capability on a 12 V system. It still requires matched state of charge at connection, matched age and model, and cabling that keeps the current share balanced. Mixing a new pack with a two-year-old one in parallel is the most common way a correctly specified installation fails early.

The six configurations we list

Two of the six are not 12 V at all — the 64 V and 76.8 V 25 Ah packs exist because low-speed electric tricycles and small EVs run 60 V and 72 V lead-acid banks, and the 20S and 24S strings above are what replace them without changing the controller. They are listed here because buyers searching for a “12 V replacement” often turn out to need one of these instead, once the old bank is counted.

ConfigurationSeriesOperating rangeMax chargeMax dischargeIP
12.8 V 25 Ah1P4S10–14.6 V25 A50 AIP67
12.8 V 50 Ah2P4S10–14.6 V50 A100 AIP67
12.8 V 75 Ah3P4S10–14.6 V75 A100 AIP67
12.8 V 100 Ah4P4S10–14.6 V100 A100 AIP67
64 V 25 Ah1P20S46–73 V12.5 A40 AIP67
76.8 V 25 Ah1P24S60–87.6 V12.5 A40 AIP67

All six are LEAWAT (Lihua) configurations taken from the 2026 manufacturer brochure. The listing reference on each product page is a configuration label rather than a manufacturer part number, and the brochure does not state cycle life for these entries — so we do not quote one. Ask for the current datasheet with the quotation if cycle life is part of your specification.

What a distributor should put in the PO

A replacement pack is a repeat item, and the terms that matter are the ones that make the second order identical to the first. The list below is what we ask for before quoting, and what we recommend a distributor fixes in writing rather than leaving to the next batch.

  • Voltage and series count — 12.8 V 4S for a 12 V bank, 64 V 20S for a 60 V bank. State the old bank’s voltage and cell count, not just “12 V”.
  • Connector and pinout — a photograph of the existing connector plus the wire gauge. Pinout is confirmed per order; it is not interchangeable between suppliers.
  • Charger arrangement — bundled, separately specified, or supplied by the customer. If a charger ships with the pack, its profile is set to the pack, not to lead-acid.
  • Labelling and packaging — private-label artwork, language of the warning label, and whether the carton needs to carry UN38.3 documentation for the shipment.
  • Warranty terms — our standard cover for custom PACKs is 12 months or 1,200 cycles, whichever comes first. Confirm how it is applied to a resold unit before promising it downstream.
  • Spares — BMS boards and connector sets held as service parts, so a failed unit in year two is a board swap rather than a pack replacement.

On volume: mixed containers are normal for distributors carrying several configurations, and the minimum order is set per project rather than per model. Send the configuration list and the destination port and the quotation will state the MOQ that applies to that mix.

Where this replacement does not work

Being explicit about the limits saves both sides a return.

  • Cranking and starting duty. A starting battery is specified by cold-cranking amps, not amp-hours. Our 25.6 V 15 Ah starting configuration is a separate product from the 12.8 V replacement line, and a 12.8 V replacement pack should not be substituted into a cranking circuit without the starting current being specified.
  • Sub-zero charging without temperature management. As above — the pack will discharge, it will not safely charge below 0 °C.
  • Applications that require a specific type approval. A replacement pack is not a certified marine, automotive or aviation component, and we do not claim those approvals. If the installation is surveyed or classed, the approval has to come from the body doing the surveying.
  • Series strings beyond the BMS rating. Four packs in series is a design decision, not a wiring decision.
  • Replacing a pack whose charger cannot be changed. If the charger is sealed, unadjustable and lead-acid only, the honest expectation is partial charge, not full capacity.

Frequently asked questions

Is a 12.8 V pack a direct replacement for a 12 V battery?

Electrically it occupies the same string position, and it is the correct nominal voltage for a 12 V lead-acid replacement. It is not a drop-in part: the charge profile, the low-voltage cutoff and the physical case all differ. Treat it as a system substitution and check the three items above.

Can I keep my existing lead-acid charger?

Only if it has a lithium profile or an adjustable absorption voltage that reaches the pack’s charge window. A charger that floats at 13.6–13.8 V will leave a 12.8 V LiFePO4 pack short of full charge. Send the charger’s model and output specification with the enquiry and it can be checked against the configuration.

How many 12.8 V packs do I need for a 48 V system?

Four, connected in series, giving 51.2 V nominal — provided the BMS is rated for series operation. If it is not, the correct answer is a single 51.2 V pack rather than four 12.8 V ones, and that is a different specification.

Why does a 100 Ah lithium pack run longer than a 100 Ah lead-acid one?

Because usable capacity differs. A lead-acid block is normally only cycled to about half its rated capacity before life drops sharply; a LiFePO4 pack is specified to a much deeper depth of discharge. The conversion economics are set out in our payback analysis, and the sizing arithmetic in how to size a battery pack.

What temperature range can these packs operate in?

Listed as 0–55 °C for charging and −20 to 60 °C for discharge across the six configurations. The charge limit is the one that requires design attention.

Do you supply to distributors rather than end users?

Yes. DIDIDEDE supplies PACKs to importers, installers and fleet workshops, with private labelling and mixed containers. Minimum order is set per project; send the configuration list and destination.

Specifications in this article are taken from the LEAWAT / Lihua 2026 manufacturer brochure as published on each product page. Dimensions, cycle life and connector details must be confirmed against the supplied configuration before ordering. Nothing here constitutes a certification of the pack for a particular vehicle, marine or aviation application.

Send your old battery spec for a replacement match

Newsletter Updates

Enter your email address below and subscribe to our newsletter